Big Green Egg
Temperature Gauge, 3 inch Dial in Tea, SD 57064
MSRP
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
17 locations / In stock at 17
In stock at 16 other locations
Tea Ace Hardware
701 N Heritage Pkwy
Tea, SD 57064
Nyberg's Ace
7210 W 41st Street
Sioux Falls, SD 57106
Nyberg's Ace Hardware
2500 W 12th Street
Sioux Falls, SD 57104
Nyberg's Ace
607 S Sycamore Ave
Sioux Falls, SD 57103
Hartford Ace Hardware
701 S Western Ave
Hartford, SD 57033
Brandon Ace Hardware
304 S Splitrock Blvd
Brandon, SD 57005
Madison Ace Hardware
800 Washington Ave S
Madison, SD 57042
Vermillion Ace Hardware
812 Cottage Ave
Vermillion, SD 57069
Orange City Ace Hardware
510 8th Street SE
Orange City, IA 51041
Elk Point Ace Hardware
609 W Main St
Elk Point, SD 57025
Riverside Ace Hardware
4200 War Eagle Dr
Sioux City, IA 51109
Laurel Ace Hardware
402 Hwy 20 S
Laurel, NE 68745
Hefner Ace Hardware
201 E Main St
Bloomfield, NE 68718
Wayne Ace Hardware
615 Dearborn St
Wayne, NE 68787
Le Mars Ace Hardware
23 1st Ave SW
Le Mars, IA 51031
Elfstrand's Ace Hardware
1420 Commerce St
Mitchell, SD 57301
Wilmes Do It Best Hardware
3049 Hamilton Blvd
Sioux City, IA 51104
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 3 inch Dial .
Write a Review