Big Green Egg
Temperature Gauge, 3 inch Dial in Springfield, IL
MSRP
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
18 locations / In stock at 18
In stock at 17 other locations
Great Lakes Ace Hardware
214 N Walnut St
Springfield, IL 62702
Great Lakes Ace Hardware
1600 Wabash Ave
Springfield, IL 62704
Scheels - Springfield
3801 S. MacArthur Blvd
Springfield, IL 62711
Petersburg Ace Hardware
420 E Sangamon St
Petersburg, IL 62675
Nena Ace Hardware
901 S. Detroit Ave
Morton, IL 61550
Sullivan Ace Hardware
435 S Hamilton St
Sullivan, IL 61951
Great Lakes Ace Hardware
204 E College Ave
Normal, IL 61761
Nena Ace Hardware
1880 Washington Rd
Washington, IL 61571
Great Lakes Ace Hardware
901 W Fayette St
Pittsfield, IL 62363
Nena Hardware
1415 W. Forrest Hill Ave.
Peoria, IL 61604
Ace Hardware
1 Airway Court
Bethalto, IL 62010
Nena Hardware
505 Jubilee Lane
Germantown Hills, IL 61548
Ace Hardware on Knoxville
8903 N Knoxville Ave
Peoria, IL 61615
Rick's Ace Hardware
2654 Northtown Way
Highland, IL 62249
Champaign Ace Hardware
2811 W Kirby Ave
Champaign, IL 61821
Ace Hardware
2021 South Neil Street
Champaign, IL 61820
Cotton's Ace Hardware of Collinsville
501 Belt Line Rd Suite 20
Collinsville, IL 62234
Ace Hardware
1320 E Street
Charleston, IL 61920
Directions
Contact
Website
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 3 inch Dial .
Write a Review
