Big Green Egg
Temperature Gauge, 3 inch Dial in McCalla, AL
MSRP
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
17 locations / In stock at 17
In stock at 16 other locations
Homewood Ace Hardware
320 Oxmoor Rd
Birmingham, AL 35209
Little Hardware Inc
2117 Cahaba Rd
Mountain Brook, AL 35223
Compton Ace Hardware
4500 Montevallo Rd
Birmingham, AL 35210
Dunnavant Valley Ace Hardware
300 Carlow Ln Ste 108
Birmingham, AL 35242
Ace of the South
255 City St
Gardendale, AL 35071
Brown Lumber & Building Supply
21891 Hwy 25
Columbiana, AL 35051
Trussville Ace Hardware
307 Main Street
Trussville, AL 35173
McFarland Ace Hardware
400 McFarland Blvd
Northport, AL 35476
Bear Creek Ace Hardware
617 Bear Creek Rd
Tuscaloosa, AL 35405
Warrior Ace Hardware
427 Caldwell Dr
Warrior, AL 35180
Curry Ace Hardware
5100 Curry Hwy
Jasper, AL 35503
Pell City Ace
2640 Martin Street S
Pell City, AL 35128
Dodge City Ace Hardware
699 AL Hwy 69 S
Hanceville, AL 35077
Weathers Hardware Appliance
109 2nd Ave E
Oneonta, AL 35121
Lake Guntersville Ace Hardware
1536 Blount Ave
Guntersville, AL 35976
McCalla Ace Hardware (Piggly Wiggly)
4750 Eastern Valley Rd
McCalla, AL 35111
Montevallo Ace Hardware
4004 Hwy 25
Montevallo, AL 35115
Directions
Contact
Website
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 3 inch Dial .
Write a Review
