Big Green Egg
Temperature Gauge, 3 inch Dial in Cutler Bay, FL
MSRP
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
14 locations / In stock at 14
In stock at 13 other locations
Ace Hardware of Cutler Bay
20537 Old Cutler Road
Miami, FL 33189
Kendall Ace Hardware
9869 SW 88th Street
Miami, FL 33176
South Dixie Ace Hardware
6448 South Dixie Highway
South Miami, FL 33143
Doral Ace Hardware
10758 NW 58th Street
Miami, FL 33178
Alton Hardgoods
1665 Alton Road
Miami Beach, FL 33139
Aventura Ace Hardware
17811 Biscayne Blvd.
Aventura, FL 33160
GW Store
147 Weston Rd
Weston, FL 33326
GW Store
3985 NW 19th St
Lauderdale Lakes, FL 33311
Ace Hardware-Margate
5843 Margate Blvd
Margate, FL 33063
Deerfield Ace Hardware
365 S Federal Highway
Deerfield Beach, FL 33441
Hessler Paint & Hardware
4591 W Atlantic Ave
Delray Beach, FL 33445
Lantana Ace Hardware
1212 Lantana Rd
Lantana, FL 33462
Rocky's Hardware-Wellington
13837 Wellington Trace
Wellington, FL 33414
Miami Home Centers - South Miami
7325 SW 57th Avenue
Miami, FL 33143
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 3 inch Dial .
Write a Review