Big Green Egg
Temperature Gauge, 3 inch Dial in Bath, ME 04530
MSRP
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
22 locations / In stock at 22
In stock at 21 other locations
Rocky's Ace Hardware
55 Congress Ave
Bath, ME 04530
Eldredge Lumber
145 Presumpscot St
Portland, ME 04103
Maine Hardware
274 St. John Street
Portland, ME 04102
Oak Hill Ace Hardware
29 Gorham Rd
Scarborough, ME 04074
Plummer's Ace Hardware
57 Main Street
Gorham, ME 04038
Plummer's Ace Hardware
42 Central Ave
Limerick, ME 04048
Rocky's Ace Hardware
873 Central Ave #108
Dover, NH 03820
Kittery Ace Hardware
6 Shapleigh Rd
Kittery, ME 03904
E.M. Heath Ace Hardware
318 Whittier Hwy
Center Harbor, NH 03226
Damariscotta Hardware
423 Main Street
Damariscotta, ME 04543
Campbell's Hardware
535 Maine Ave
Farmingdale, ME 04344
EL Spear Lumber & Hardware
10 Payne Ave
Rockland, ME 04841
Aubuchon Hardware
499 Roosevelt Trail
Naples, ME 04055
Campbell's Hardware
30 Garland Rd
Winslow, ME 04901
Aubuchon Hardware
485 Kennedy Memorial Dr
Waterville, ME 04901
Aubuchon Hardware
528 Wilton Rd
Farmington, ME 04983
Aubuchon Hardware
231 Northport Ave
Belfast, ME 04983
Campbell's Hardware
398 Madison Ave
Skowhegan, ME 04976
Campbell's Hardware-Aubuchon Hardware
66 Main Street
Madison, ME 04950
Aubuchon Hardware
83 Moosehead Trail
Newport, ME 04953
Aubuchon Hardware
7 Main Street
Alton, NH 03809
Aubuchon Ace Hardware
41 Concord Rd
Lee, NH 03861
Directions
Contact
Website
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 3 inch Dial .
Write a Review
