Big Green Egg
Temperature Gauge, 3 inch Dial in Ada, OK
MSRP
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
17 locations / In stock at 17
In stock at 16 other locations
JB's Ace Home Center
1407 N. Country Club Rd.
Ada, OK 74820
Pauls Valley ACE Hardware
1340 W. Grant Ave.
Pauls Valley, OK 73075
Wyrick Lumber Company
721 W 13th Street
Atoka, OK 74525
Robbins Ace of Purcell
2206 State Hwy 74
Purcell, OK 73080
Kingston Ace Hardware
23 N Main Street
Kingston, OK 73439
Harrah Supply
2390 Church Ave
Harrah, OK 73045
Ace Hardware & Garden Center
987 E Veterans Memorial Hwy
Blanchard, OK 73010
West Lake Ace Hardware 75
11801 S. Western
Oklahoma City, OK 73170
Westlake Hardware #84
212 N Air Depot Blvd
Midwest City, OK 73110
Ace Hardware of Newcastle
3009 Bypass Rd
Newcastle, Ok 73065
Fletcher Ace Hardware
512 W FM 120
Pottsboro, TX 75076
Westlake Ace Hardware
1509 W Britton Rd
Oklahoma City, OK 73120
Duncan Ace Hardware
1713 N Highway 81
Duncan, OK 73533
Westlake Ace Hardware
6951 Northwest Expressway
Oklahoma City, OK 73132
Westlake Hardware
821 W. Danforth
Edmond, OK 73003
Wyrick Lumber Company
801 E Main Street
Tishomingo, OK 73460
County Bldg Center Ace Hardware
821 W Main
Ardmore, OK 73401
Directions
Contact
Website
Product Information
This high quality, stainless steel temperature gauge - with a large, easy-to-read 3 inch dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures Oversized 3 in (8 cm) Dial Stainless Steel External Temperature Gauge - 117250
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 3 inch Dial .
Write a Review
