Big Green Egg
Temperature Gauge, 2 inch Dial in Gloucester, VA 23061
MSRP
Product Information
This high quality, stainless steel temperature gauge - with an easy-to-read dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures 2 in Dial Stainless Steel External Temperature Gauge - 117236
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
16 locations / In stock at 16
In stock at 15 other locations
Horn's Gloucester Ace Hardware
7307 John Clayton Memorial Hwy
Gloucester, VA 23061
Ace Peninsula Hardware
210 Monticello Ave
Williamsburg, VA 23185
West Point Ace Hardware
611 14th Street
West Point, VA 23181
Grafton Ace Hardware
4914 George Washington Memorial Hwy
Grafton, VA 23692
Northern Neck Ace Hardware
96 School St
Kilmarnock, VA 22482
Peninsula Ace Hardware
12490 Warwick Blvd
Newport News, VA 23606
Peninsula Ace Hardware Hampton
7 Towns Center Way
Hampton, VA 23666
Ace Peninsula Hardware
2098 Nickerson Blvd
Hampton, VA 23663
Horn's Warsaw Ace
19 Main Street
Warsaw, VA 22572
Costello's Ace Hardware - Colonial Beach
535 Euclid Ave
Colonial Beach, VA 22443
Costello's Ace Hardware - Ridge Rd
11475 Ridge Road
King George, VA 22485
Sneade's Ace Home Center
30314 Triangle Dr
Charlotte Hall, MD 20622
Courtland Ace Hardware
(1 Review)
9795 Courthouse Rd
Spotsylvania, VA 22553
Costello's Ace Hardware of La Plata
6655 Crain Highway
La Plata, MD 20646
Northwest Ace Hardware - Blackstone
109 N High St
Blackstone, VA 23824
Ace Hardware of Amelia
15139 Patrick Henry Hwy
Amelia Court House, VA 23002
Directions
Contact
Website
Product Information
This high quality, stainless steel temperature gauge - with an easy-to-read dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures 2 in Dial Stainless Steel External Temperature Gauge - 117236
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 2 inch Dial .
Write a Review
