Big Green Egg
Temperature Gauge, 2 inch Dial in Beaumont, TX
MSRP
Product Information
This high quality, stainless steel temperature gauge - with an easy-to-read dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures 2 in Dial Stainless Steel External Temperature Gauge - 117236
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Select a Store
Selected Store
16 locations / In stock at 16
In stock at 15 other locations
M & D Supply
4580 College St
Beaumont, TX 77707
M & D Supply Ace Hardware
122 S Main Street
Lumberton, TX 77657
Stine Lumber Co.
2950 S Ruth St
Sulphur, LA 70663
Stine Lumber Co.(Lake Charles)
4501 Nelson Rd
Lake Charles, LA 70605
Westwood Ace Hardware TIY
2365 Westwood Rd
Westlake, LA 70669
J&R's Ace Hardware
23678 FM 1314 Rd
Porter, TX 77365
M & D Supply Ace Hardware
2422 Bay Area Blvd. #A
Houston, TX 77058
League City Ace Hardware
1915 West League City Pkwy
League City, TX 77573
Stine Home and Yard
1335 North Pine
DeRidder, LA 70634
Pearland Lumber & Ace Hardware
2027 N Main St
Pearland, TX 77581
Spring Ace hardware
1721 Spring Cypress Rd.
Spring, TX 77388
Ace Hardware of The Woodlands
10720 Kuykendahl Road
The Woodlands, TX 77381
M&D Supply Ace Hardware
12458 Eagle Dr Ste 300
Mont Belvieu, TX 77535
Bacliff Ace Hardware
607 Grand Ave
Bacliff, TX 77518
EJ's Ace Hardware
4392 US-190 W
Livingston, TX 77351
Spring Branch Ace Hardware
7840 Long Point Rd
Houston, TX 77055
Directions
Contact
Website
Product Information
This high quality, stainless steel temperature gauge - with an easy-to-read dial - precisely monitors the temperatures inside the dome of an EGG, allowing you to achieve and maintain precise cooking temperatures 2 in Dial Stainless Steel External Temperature Gauge - 117236
- 750F deg / 400C deg
- Works with XXLarge, XLarge, Large, Medium, Small and MiniMax EGGs
- Heavy duty construction, hermetically sealed
- Designed and manufactured in the USA
Installation:
- Carefully insert stem from the outside through small hole in dome of the EGG; the silicone washer should remain on the outside of the EGG.
- Carefully reach inside the dome, and slide retaining clip onto the stem. Squeeze the clip so that it slides easily.
- Slide clip up the stem until the silicone washer -x001F-ts snugly against the exterior of the dome. For accurate reading, thermometer must be installed past the groove on the lower portion of stem as shown below.
This thermometer is calibrated and adjusted at the factory. If you are in high altitudes or wish to check the calibration:
- Bring a clean container of water to a boil.
- Carefully place the end of the thermometer probe into boiling water past the groove on the lower portion of stem. Leave immersed for at least one minute taking care not to let the probe rest on or make contact with the container.
- Boiling point will read 212 deg F/100 deg C at sea level. Boiling point decreases approx 2 deg with each 1000' of altitude. If the thermometer does not read 212 deg F/100 deg C at sea level, calibration can be reset by carefully holding the thermometer head and turning the hex nut with a wrench to move dial in one direction or the other.
- CAUTION - Do not adjust hot thermometer with bare hands!
- CAUTION - Do not hold thermometer with bare hands while placing in boiling water as burns can result!
- CAUTION - Thermometer tip is sharp, do not leave unattended or place within reach of children.
Product Reviews
There are no reviews yet for Big Green Egg: Temperature Gauge, 2 inch Dial .
Write a Review
